Kia Sephia/Shuma/Spectra

since 1995 of release

Repair and car operation



KIA of Sefia / Noise/range
+ 2. Engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. Automatic transmission
- 11. Axes and power shafts
   11.1. Specifications
   11.2. Check люфта bearings of forward wheels
   11.3. Check of a condition of a power shaft
   11.4. Rotary fist and nave of a forward wheel
   11.5. Back axis
   11.6. Power shaft
   11.7. Repair of a rotary fist
   11.8. Type CV JOINT Tripoid
+ 12. Steering
+ 13. Wheels and tires
+ 14. Brake system
+ 15. Suspension bracket
+ 16. Body
+ 17. Central air
+ 18. Electric equipment


a7a4cf13


11.4. Rotary fist and nave of a forward wheel

GENERAL INFORMATION

Rotary fist and nave of a forward wheel

1–wheel;
2–a nut with a fillet;
3–support of a forward brake;
4–brake disk;
5–tip of steering draft;
6–spherical hinge of the bottom lever;
7–rotary fist and nave of a forward wheel

Removal

PERFORMANCE ORDER
1. Lift the car and fix on support.
2. Turn out four nuts of fastening of a wheel.
3. Remove a wheel.
4. Unbend a fillet and unscrew a nut of fastening of a power shaft to a nave and turn out two bolts of fastening of a brake disk.
5. Remove a support and a brake disk.

Prevention

Do not damage a dustproof cover.


6. Take шплинт and unscrew a nut of fastening of a pin of the spherical hinge of a tip of steering bent for to a rotary fist. A stripper OK130 283 021 squeeze out a pin of the spherical hinge from a rotary fist.
7. Disconnect an earring of the stabilizer of cross-section stability from the bottom cross-section lever of a forward suspension bracket.
8. Turn out a coupling bolt, mount wring out the bottom lever down, and separate a hinge pin from a rotary fist.
9. Note situation and turn out bolts of fastening of the lower part of a rack of a forward suspension bracket to a rotary fist. Remove a rotary fist and a nave of a forward wheel.

10. Check a condition of all details and, if necessary, restore or replace the damaged details.

Installation

PERFORMANCE ORDER
1. Establish a rotary fist and a nave of a wheel fix bolts to the lower part of a rack of a forward suspension bracket.
2. Establish a pin of the spherical hinge of the bottom lever in a rotary fist and fix a coupling bolt and a nut.

Inhaling moment: 43–54 N • m

3. Establish a brake disk on a nave of a wheel and fix two bolts.

Inhaling moment: 10–15 N • m

4. Establish a support of a forward brake on a rotary fist and fix two bolts.

Inhaling moment: 45-68 N • m


Prevention

Do not damage a dustproof cover.


5. Establish a pin of the spherical hinge of a tip of steering draft in a rotary fist.
6. Screw nuts and shplinty, fix them from an otvorachivaniye.

Inhaling moment: 29–44 N • m

7. Screw a new nut with a fillet and hammer a nut fillet into a groove of a power shaft.

Inhaling moment: 210–279 N • m

8. Establish a wheel.

9. Tighten nuts of fastening of a wheel.

Inhaling moment: 88–118 N • m

10. Freely screw nuts of fastening of an earring of the stabilizer, lower the car and, on the car standing on wheels, tighten nuts.

Inhaling moment: 43–61 N • m

11. Check corners of installation of forward wheels.