Kia Sephia/Shuma/Spectra

since 1995 of release

Repair and car operation

10.11. The case of the regulating valve

GENERAL INFORMATION

Prevention

At work with the regulating valve be especially careful as it consists a large number of exact details. At removal have details in a certain order not to mix them. Clear the removed details solvent and dry up them the compressed air. Clean all openings and channels the compressed air.

The case of the regulating valve

1–block of the mesh filter;
2–a sealing ring to (replace);
3–oil pipeline;
4–a sealing ring of round section to (replace);
5–the switching solenoid A (1–2 solenoid);
6–solenoid of coupling of the converter of a torque;
21-mesh filters;

22-rubber balls;
23-the preliminary case of the regulating valve;
24-laying Е to (replace);
25-bottom plate of a separator;
26-oil filter;
27-laying of F to (replace);
28-mesh filter;
29-the bottom case of the regulating valve

The case of the regulating valve

7–linear electromagnetic valve;
8–switching solenoids B and C;
9–the top case of the regulating valve;
10-laying to (replace);
11-screws;
12-top plate of a separator;
13-oil filter;

14-laying In to (replace);
15-the main case of the regulating valve;
16-laying With to (replace);
17-screws;
18-main plate of a separator;
18-laying of D to (replace);
20-rubber balls;

Removal

PERFORMANCE ORDER

1. Turn out bolts and remove an oil pipeline.
	2. Remove sealing rings from an oil pipeline.
3. Remove switching solenoid and the mesh filter.
	4. Remove the solenoid of coupling of the converter of a torque and the mesh filter.
	5. Remove switching solenoids B and C and mesh filters.
	6. Remove the linear electromagnetic valve.
	7. Turn out nine bolts of fastening of the top case of the regulating valve.
8. Turn out two screws.
	9. Remove B laying, the top plate of a separator, the oil filter and A laying.
	10. Turn out seven bolts and remove the main regulating valve.
11. Turn out two screws.
	12. Remove laying of D, the main plate of a separator and laying of C.
	13. Remove three rubber balls from the main case of the regulating valve.
	14. Remove the oil mesh filter and two rubber balls from the additional main case of the regulating valve.
	15. Turn out six bolts and remove the additional main case of the regulating valve.
	16. Remove E laying, the bottom plate of a separator, the oil filter and F laying.
	17. Remove the oil mesh filter from the bottom case of the regulating valve.

Arrangement of the oil filter on the bottom party of the additional main case of the adjusting valve

Arrangement of the oil filter on the top party of the case of the adjusting valve

Arrangement of the oil filter on the top case of the adjusting valve

Installation

Installation sites and length of bolts of fastening of details of the regulating valve

PERFORMANCE ORDER

1. Establish the oil mesh filter in the bottom case of the regulating valve.
	2. Establish the oil filter in the bottom plate of a separator.
Prevention Laying of F and laying of E are not interchangeable. They are identified by a form in the area shown in drawing.

3. Establish F laying, on a plate of a separator and new laying of E on the bottom case of the valve
	4. Establish the additional main case of the regulating valve on the bottom case and fix seven bolts. Inhaling moment: 7,9–10,7 N • m
	5. Establish two rubber balls and oil mesh filters in the additional main case of the regulating valve.
	6. Establish rubber balls in the main case of the regulating valve.
Prevention Laying With and laying of D are not interchangeable. They are identified by a form in the area shown in drawing.
	7. Establish new laying of C, a plate of a separator and laying of D on the main case of the regulating valve.
8. Fix laying of C, a plate of a separator and laying of D to the main case two bolts. Inhaling moment: 1,27–1,86 N • m
9. Establish the main case of the regulating valve on the additional main case of the regulating valve.
Prevention Arrange heads of bolts as is shown in drawing.
	10. Freely screw bolts.
	11. Establish the oil filter in the top plate of a separator.
Prevention Laying And and laying In are not interchangeable. They are identified by a form in the area shown in drawing.
	12. Establish new laying of A, the top plate of a separator and new laying of B on the top case of the regulating valve.
	13. Two bolts fix to the main case of the regulating valve A laying, the top plate of a separator and B laying.
	14. Establish the top case of the regulating valve on the main case of the regulating valve and fix nine bolts. Inhaling moment: 7,9–10,7 N • m
Prevention Arrange heads of bolts as is shown in drawing.
15. Freely screw bolts of fastening of the bottom case of the regulating valve.
	16. Establish the linear electromagnetic valve. Inhaling moment: 7,9–10,7 N • m
	17. Establish solenoids B and C, oil mesh filters and an arm.
	18. Tighten bolts the demanded moment. Inhaling moment: 7,9–10,7 N • m
	19. Establish coupling of the converter of a torque and the oil mesh filter. Inhaling moment: 7,9–10,7 N • m
20. Establish the solenoid of switching and the oil mesh filter on the top case of the valve. Inhaling moment: 7,9–10,7 N • m
21. Grease with liquid for an automatic transmission sealing rings and establish them on an oil pipeline.
	22. Establish an oil pipeline and fix it bolts. Inhaling moment: 7,9–10,7 N • m
23. Grease with liquid for an automatic transmission sealing rings and establish them on the block of the mesh filter
	24. Establish the oil mesh filter on the case of the regulating valve and fix it three bolts. Inhaling moment: 7,9–10,7 N • m