Kia Sephia/Shuma/Spectra

since 1995 of release

Repair and car operation


KIA of Sefia / Noise/range
+ 2. Engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. Automatic transmission
+ 11. Axes and power shafts
+ 12. Steering
+ 13. Wheels and tires
+ 14. Brake system
- 15. Suspension bracket
   15.1. Specifications
   15.2. Check and adjustment of corners of installation of wheels
   15.3. Bottom lever of a forward suspension bracket
   15.4. Forward stabilizer of cross-section stability
   15.5. Cross-section drafts and longitudinal lever of a back suspension bracket
   15.6. Back stabilizer of cross-section stability
   15.7. Cross-section beam of a back suspension bracket
   15.8. Repair of an amortization rack of a forward suspension bracket
   15.9. Repair of an amortization rack of a back suspension bracket
+ 16. Body
+ 17. Central air
+ 18. Electric equipment

a7a4cf13

15.7. Cross-section beam of a back suspension bracket

 Removal
PERFORMANCE ORDER
1. Lift a back part of the car and fix on support.
2. Remove a wheel.
3. Turn out a bolt and remove a washer of fastening of forward cross-section bent for to a cross-section beam.
4. Turn out a bolt and remove a washer of fastening of back cross-section bent for to a cross-section beam.
5. Turn out a nut and remove a sharnirny bolt of fastening of cross-section bent for to a support of a back nave.
6. Turn out two sharnirny bolts of fastening of the longitudinal lever of a back suspension bracket.
7. Remove the longitudinal lever of a back suspension bracket.
8. Turn out nuts of fastening of an earring of the stabilizer of cross-section stability.
9. Turn out a bolt of fastening of an earring of the stabilizer and remove stabilizer earrings
10. Turn out an assembly bolt of fastening of an arm of the stabilizer and the plug of an arm of the stabilizer.
11. Remove the stabilizer of cross-section stability.
12. Turn out three bolts of fastening of an arm of a cross-section beam, then turn out one bolt of fastening of a cross-piece to a cross-section beam.
13. Remove a cross-section beam.

Installation
PERFORMANCE ORDER
1. Screw one bolt of fastening of a cross-piece to a cross-section beam, then screw three bolts of fastening of an arm of a cross-section beam.

Inhaling moment: 46–57 N • m
2. Establish the stabilizer of cross-section stability.
3. Put greasing on the stabilizer plug.
4. Establish stabilizer plugs according to the adjusting labels put on the stabilizer.
5. Establish arms of the stabilizer and fix bolts.
6. Screw a bolt of fastening of an earring of the stabilizer to a cross-section beam.

Inhaling moment: 43–61 N • m
7. Screw nuts of fastening of an earring of the stabilizer to the stabilizer.

Inhaling moment: 43–61 N • m
8. Establish the longitudinal lever of a back suspension bracket in an arm and on a support of a nave and fix two bolts.

Inhaling moment: 43–61 N • m
9. Establish cross-section drafts on a support of a nave and fix the sharnirny bolt, two washers and a spring washer, then tighten a lock nut.

Inhaling moment: 93–117 N • m
10. Establish forward cross-section draft and fix it a bolt and a lock washer to a cross-section beam.

Inhaling moment: 93–117 N • m
11. Establish back cross-section draft and fix it a bolt and a lock washer to a cross-section beam.

Inhaling moment: 93–117 N • m
12. After installation, check corners of installation of back wheels.