Kia Sephia/Shuma/Spectra

since 1995 of release

Repair and car operation

KIA of Sefia / Noise/range
+ 2. Engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. Automatic transmission
+ 11. Axes and power shafts
+ 12. Steering
+ 13. Wheels and tires
+ 14. Brake system
- 15. Suspension bracket
   15.1. Specifications
   15.2. Check and adjustment of corners of installation of wheels
   15.3. Bottom lever of a forward suspension bracket
   15.4. Forward stabilizer of cross-section stability
   15.5. Cross-section drafts and longitudinal lever of a back suspension bracket
   15.6. Back stabilizer of cross-section stability
   15.7. Cross-section beam of a back suspension bracket
   15.8. Repair of an amortization rack of a forward suspension bracket
   15.9. Repair of an amortization rack of a back suspension bracket
+ 16. Body
+ 17. Central air
+ 18. Electric equipment

15.3. Bottom lever of a forward suspension bracket

GENERAL INFORMATION

Bottom lever of a forward suspension bracket

1–nut of fastening of an earring of the stabilizer;
2–sharnirny bolt;
3–assembly bolts;
4–coupling bolt of fastening of a pin of the spherical hinge;
5–lock nut;
6–washers;
7–back plug;

8–nuts;
9–bolts;
10-spherical hinge of the bottom lever;
11-a protective cover of the spherical hinge to (replace);
12-forward plug;
13-bottom lever of a forward suspension bracket

Removal

PERFORMANCE ORDER

1. Lift a forward part of the car and fix on support.
2. Remove a wheel.
3. Turn out a nut of fastening of an earring of the stabilizer to the bottom lever of a forward suspension bracket.
4. Turn out a sharnirny bolt.
5. Turn out a nut and remove a bolt of fastening of a pin of the spherical hinge to a rotary fist.
6. Turn out three assembly bolts.
7. Turn out a lock nut and remove a washer and a back part of the plug of the bottom lever of a forward suspension bracket.
8. Turn out two nuts and remove bolts of fastening of the spherical hinge to the bottom lever of a forward suspension bracket.
9. Fix the spherical hinge in a vice.
	10. Gradually, being careful and moving a chisel round the hinge, bring down a protective cover.
Prevention Do not damage the surface of the hinge adjoining to a protective cover.
11. Remove the forward plug of the bottom lever of a forward suspension bracket.
12. Remove the bottom lever of a forward suspension bracket.

Installation

PERFORMANCE ORDER

1. Put a small amount of greasing in a protective cover of the spherical hinge.
	2. A press and an opravka establish a protective cover on the spherical hinge.
3. Establish the spherical hinge on the bottom lever of a forward suspension bracket and fix it two bolts and nuts. Inhaling moment: 93–117 N • m
4. Establish the back plug on the bottom lever of a forward suspension bracket with two washers and tighten a lock nut. Inhaling moment: 93–117 N • m
5. Tighten three assembly bolts. Inhaling moment: 93–117 N • m
6. Establish a pin of the spherical hinge in a rotary fist and fix a bolt and a nut. Inhaling moment: 43–54 N • m
7. Establish the forward plug on the bottom lever of a forward suspension bracket and tighten a sharnirny bolt. Inhaling moment: 93–117 N • m
8. Screw a nut of fastening of an earring of the stabilizer to the bottom lever of a forward suspension bracket. Inhaling moment: 43-61 N • m

Prevention

Tighten bolts and nuts of fastening of the bottom lever of a forward suspension bracket the demanded moment before car lowering (without loading).

Tighten bolts and nuts of fastening of forward and back plugs of the bottom lever of a forward suspension bracket after car installation on wheels (under loading).

Check

PERFORMANCE ORDER

Fix the special tool OK130 322 020 on a pin of the spherical hinge of the bottom lever of a forward suspension bracket and measure a torque which is necessary for putting for a hinge provorachivaniye.

The moment for a hinge provorachivaniye: 2,0–3,4 N • m