Kia Sephia/Shuma/Spectra

since 1995 of release

Repair and car operation



KIA of Sefia / Noise/range
+ 2. Engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. Automatic transmission
+ 11. Axes and power shafts
+ 12. Steering
+ 13. Wheels and tires
- 14. Brake system
   14.1. Specifications
   14.2. Pumping of hydraulic system of a drive of brakes
   14.3. Check of brake tubes and hoses
   14.4. Replacement of brake hoses
   14.5. Height of installation of a pedal of a brake
   14.6. Free wheeling of a pedal of a brake
   14.7. Distance of a pedal of a brake from a floor
   14.8. Check of the vacuum amplifier of brakes
   14.9. Parking brake
   14.10. Brake pedal
   14.11. Main brake cylinder
   14.12. Vacuum amplifier of brakes
   14.13. Replacement of forward brake shoes
   14.14. Replacement of brake shoes on back drum-type brakes
   14.15. Replacement of brake shoes on back disk brakes
   14.16. Parking brake
   14.17. Block of hydraulic management (HCU)
   14.18. Forward sensor of frequency of rotation of a wheel
   14.19. Back sensor of frequency of rotation of a wheel
   14.20. Gear rotor of the sensor of frequency of rotation of a wheel
   14.21. Repair of the working brake cylinder
   14.22. Main survey
   14.23. Check of functionality
   14.24. List of codes of malfunctions of brake system
+ 15. Suspension bracket
+ 16. Body
+ 17. Central air
+ 18. Electric equipment


a7a4cf13

14.15. Replacement of brake shoes on back disk brakes

GENERAL INFORMATION

Brake shoes on back disk brakes

1–cable of the parking brake and clip of fastening of a cable;
2–connecting bolt;
3–brake tube;
4–a directing bolt;
5–support;
6–V-shaped spring;

7–brake shoe;
8–laying;
9–a directing plate;
10-bolt;
11-holder of a support;
12-support piston

Removal

PERFORMANCE ORDER
1. Remove a clip and disconnect a cable of the parking brake.
2. Turn out a connecting bolt of fastening of a brake tube to a support.
3. Press a back brake hose.
4. Turn out two directing bolts of fastening of a support.
5. Remove a support from a brake disk.
6. Remove two V-shaped springs of fastening of brake shoes.
7. Remove brake shoes, laying and directing plates.
8. Turn out two bolts of fastening of the holder of a support.
9. Remove the holder of a support.

Check

PERFORMANCE ORDER
1. Measure thickness of brake shoes.

Thickness of brake shoes:
The nominal: 10,0 mm
The minimum admissible: 2,0 mm
2. By the indicator of hour type measure palpation of a brake disk.

Maximum palpation: 0,08 mm
3. Measure thickness of a brake disk.

Thickness of a brake disk:
The nominal: 10 mm
The minimum admissible: 8 mm

Installation

PERFORMANCE ORDER
1. Establish the holder of a support and fix it two bolts.

Inhaling moment: 45–67 N • m
2. Establish directing plates.
3. Establish brake shoes and laying and fix them two V-shaped springs.
4. The special adaptation OK9A4 263 001 press the piston into a support in order that it was possible to establish a support on new brake shoes.
5. Tighten two directing bolts of fastening of a support.

Inhaling moment: 29–39 N • m
6. Connect to a support a brake tube and fix it a connecting bolt.

Inhaling moment: 22–29 N • m
7. Establish a cable of the parking brake and fix it a clip.
8. Remove air from a hydraulic contour of brake system.
9. Check absence of leakages of brake liquid.