Kia Sephia/Shuma/Spectra

since 1995 of release

Repair and car operation



KIA of Sefia / Noise/range
+ 2. Engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. Automatic transmission
+ 11. Axes and power shafts
+ 12. Steering
+ 13. Wheels and tires
+ 14. Brake system
+ 15. Suspension bracket
+ 16. Body
+ 17. Central air
- 18. Electric equipment
   18.1. Specifications
   18.2. Electric chains
   18.3. Safety locks
   18.4. Storage battery
   18.5. Check of level and density of electrolit and charging
   18.6. Unattended batteries
   18.7. Wires and plugs
   18.8. Charging of standard batteries
   18.9. Starter
   18.10. Switch of blocking of a starter
   18.11. Removal and starter installation
   18.12. Starter repair
   18.13. Check of the traction relay
   18.14. Check of brushes and shchetkoderzhatel
   18.15. Check of coils of a stator
   18.16. Rotor check
   18.17. Generator
   18.18. Belt of a drive of the generator
   18.19. Removal and generator installation
   18.20. Generator repair
   18.21. Check of a heater of back glass
   18.22. Safety cushion of the driver
   18.23. Safety cushion of the forward passenger
   18.24. Spiral wire
   18.25. Diagnostics of malfunctions of system of start-up and methods of their elimination
   + 18.26. Electric circuits


a7a4cf13

18.16. Rotor check

PERFORMANCE ORDER
1. An ohmmeter check conductivity between brushes of a collector and a rotor. In the presence of conductivity, replace a rotor.
2. An ohmmeter check conductivity between brushes of a collector and rotor shaft. In the presence of conductivity, replace a rotor.
3. Establish a rotor on V-shaped blocks and, the indicator of hour type, check collector palpation. If palpation exceeds maximum permissible value, pierce a collector or replace a rotor.

Nominal palpation: 0,05 mm
Maximum permissible palpation: 0,4 mm
4. Measure diameter of a collector. If diameter less than the demanded size, replace a rotor.

Diameter of a collector: 31 mm
5. If the surface of a collector is polluted, wipe it. If necessary, pierce or process a collector an emery paper.
6. If depth of flutes between contact plates of a collector less maximum permissible size, replace a rotor.

Nominal depth; 0,5–0,8 mm
Maximum permissible depth: 0,2 mm

Assembly

PERFORMANCE ORDER
1. Establish earlier removed washers on a rotor shaft.
2. Establish a rotor in the stator case.
3. Establish a shchetkoderzhatel in a back cover and fix screws.

Inhaling moment: 2,4–4,4 N • m
4. Establish the obgonny coupling and a clamp of a lock ring on a rotor shaft.
5. Establish a lock ring in a flute of a shaft of a rotor.
6. Establish a clamp of a lock ring on a lock ring.
7. Establish the lever.
8. At existence establish planetary transfer.
9. Establish a forward cover.
10. From a back cover establish, and return hairpins.

Inhaling moment: 3,8–7,1 N • m
11. Insert a plunzher into the lever.
12. Insert a spring of the traction relay.
13. Establish the traction relay and fix screws.

Inhaling moment: 4,1–7,6 N • m
14. Submit tension of the storage battery to the plug S and the case of the traction relay and check that the plunzher is nominated outside and stops.
15. Measure a gap between a clamp of a lock ring and a flange of a forward cover.

Gap: 0,5–2,0 mm

Prevention

Do not submit tension of the storage battery on the traction relay during more than 10 pages.


16. If the gap differs from demanded, adjust it increasing or reducing number of laying between the traction relay and a forward cover.
17. Connect a wire of the coil of a stator to the plug M of the traction relay.