Kia Sephia/Shuma/Spectra

since 1995 of release

Repair and car operation



KIA of Sefia / Noise/range
+ 2. Engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. Automatic transmission
+ 11. Axes and power shafts
+ 12. Steering
+ 13. Wheels and tires
+ 14. Brake system
+ 15. Suspension bracket
- 16. Body
   16.1. Specifications
   16.2. Front bumper
   16.3. Rear bumper
   16.4. Forward door
   16.5. Vlagozashchitnoye door consolidation
   16.6. Hinges of a door and shock plate of the lock of a door
   16.7. Door lock
   16.8. Internal handle of opening of a door
   16.9. External handle of a door
   16.10. Cylinder of the lock of a door
   16.11. Switches of window regulators
   16.12. A window regulator with an electric drive
   16.13. Door glass
   16.14. Back door
   16.15. Headlight
   16.16. Top stoplight
   16.17. The back combined lamp
   16.18. Ceiling
   16.19. Cowl
   16.20. Sound signal
   16.21. Combination of devices
   16.22. Repair of a combination of devices
   16.23. Replacement of filament lamps of a combination of devices
   16.24. Printed-circuit board
   16.25. Top decorative overlay of the dashboard
   16.26. Switches
   16.27. Central panel
   16.28. Overlay of the central console
   16.29. Central console
   16.30. Regulator of illumination of the dashboard
   16.31. Left and right lattices of a heater of a windscreen
   16.32. Left and right lateral lattices of a heater
   16.33. Air lines of system of heating and ventilation
   16.34. Floor air lines
   16.35. Ware box
   16.36. Cable of opening of the lock of a cowl
   16.37. Handle of opening of the lock of a cowl
   16.38. Dashboard
   16.39. Control panel heating and ventilation
   16.40. External rear-view mirror
   16.41. Replacement of glass of an external rear-view mirror
   16.42. Forward seats
   16.43. Upholstery of a back of a forward seat
   16.44. Upholstery of a pillow of a forward seat
   16.45. The leaning-back hinge of a forward seat
   16.46. Back sitting
   16.47. Seat belts
   16.48. Clamp of a forward seat
   16.49. Forward humeral seat belt
   16.50. Seat belts of a back seat
   16.51. Bracket of fastening of a back seat belt
   16.52. Humeral back seat belt
   16.53. Top furnish of a forward rack
   16.54. Bottom furnish of the central rack
   16.55. Top furnish of the central rack
   16.56. Furnish of a back rack
   16.57. Support furnish for a foot
   16.58. Upholstery of a forward door
   16.59. Upholstery of a back door
   16.60. Trunk lid
   16.61. Trunk lid hinge
   16.62. Hoses of a washer of a windscreen
   16.63. Engine of a washer of a windscreen
   16.64. Screen wiper lever
   16.65. Sprays
   16.66. Replacement of brushes of a screen wiper
   16.67. Drafts of a screen wiper
   16.68. Screen wiper engine
   16.69. Distances between body points
+ 17. Central air
+ 18. Electric equipment


a7a4cf13

16.68. Screen wiper engine

Check

PERFORMANCE ORDER
1. An ohmmeter check conductivity between contacts of the socket of the engine. In the situation OFF conductivity should be between contacts 1 and 4, in the situation LOW – between contacts 1 and 3, and in the situation HIGH – between contacts 2 and 3.
2. If conductivity is absent, replace the engine.
3. Check frequency of rotation of the engine when giving by additional wires of tension of the storage battery on contacts of the socket of the engine. Connect the negative plug of the storage battery to contact 3 sockets. At connection of the positive plug of the storage battery to contact 1 engine should rotate with low frequency of rotation, and at connection to contact the 2nd engine should rotate with high frequency of rotation.

Removal

PERFORMANCE ORDER
1. Disconnect a wire from the negative plug of the storage battery.
2. Disconnect the socket of a plait of wires from the screen wiper engine.
3. Turn out four bolts of fastening of the engine of a screen wiper.
4. A screw-driver separate draft of a screen wiper from a crank of the engine of a screen wiper.
5. Remove the screen wiper engine.

Installation

PERFORMANCE ORDER
1. Establish draft of a screen wiper on an engine crank.
2. Establish the engine of a screen wiper and fix it four bolts.
      
Inhaling moment: 7–10 N • m
3. Connect the socket of a plait of wires to the screen wiper engine.
4. Connect a wire to the negative plug of the storage battery.