Kia Sephia/Shuma/Spectra

since 1995 of release

Repair and car operation

KIA of Sefia / Noise/range
+ 2. Engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. Automatic transmission
+ 11. Axes and power shafts
+ 12. Steering
+ 13. Wheels and tires
+ 14. Brake system
- 15. Suspension bracket
   15.1. Specifications
   15.2. Check and adjustment of corners of installation of wheels
   15.3. Bottom lever of a forward suspension bracket
   15.4. Forward stabilizer of cross-section stability
   15.5. Cross-section drafts and longitudinal lever of a back suspension bracket
   15.6. Back stabilizer of cross-section stability
   15.7. Cross-section beam of a back suspension bracket
   15.8. Repair of an amortization rack of a forward suspension bracket
   15.9. Repair of an amortization rack of a back suspension bracket
+ 16. Body
+ 17. Central air
+ 18. Electric equipment

15.8. Repair of an amortization rack of a forward suspension bracket

GENERAL INFORMATION

Elements of an amortization rack of a forward suspension bracket

1–lock nut of a rod;
2–spring washer;
3–steel plate;
4–top support of a rack;
5–rack bearing;
6–top nest of a spring;
7–top laying of a spring;

8–dustproof cover;
9–buffer;
10-cylindrical spring;
11-bottom laying of a spring;
12-bottom nest of a spring;
13-shock-absorber

Removal

PERFORMANCE ORDER

1. Remove a forward spring, and the shock-absorber.
2. Turn out four assembly bolts.
3. Fix the top support of a rack in a vice.
Prevention Close sponges of a vice plates from a soft material.
	4. Weaken a lock nut on two-three turns.
Prevention Do not turn out completely a nut.
5. The special adaptation OK2A1 341 001 compress a spring of a rack of a forward suspension bracket.
6. Turn out a lock nut and remove a washer.
	7. Note the provision of the top support of a rack of a forward suspension bracket, then remove it. Remove the top nest of a spring, the top laying of a spring, a cylindrical spring, a protective cover, an emphasis, the bottom laying of a spring and the bottom nest of a spring.

Check

PERFORMANCE ORDER

Check the following details of a rack of a forward suspension bracket and, if necessary, replace them:
   a. undertake a hand a rod of the shock-absorber and several times press and extend it from the shock-absorber;
   b. check that the rod moves smoothly, without jammings and the effort enclosed to a rod does not change with each course;
   c. be convinced that when moving a rod there are no extraneous noise.

Assembly

PERFORMANCE ORDER

1. Fix the shock-absorber in a vice.
Prevention Close sponges of a vice plates from a soft material.
2. The special adaptation OK2A1 341 001 compress a spring of a rack of a forward suspension bracket.
3. Establish a cylindrical spring, having established the bottom end of a spring in dredging.
	4. Establish the buffer.
5. Put special greasing for rubber on an emphasis and the top nest of a spring.
6. Establish the top laying and a spring nest.
7. Establish the top support of a rack in its initial situation.
8. Establish a washer and a lock nut of a rod and tighten it, a little.
	9. Remove the special adaptation OK2A1 341 001 for spring compression.
Prevention Check that the cylindrical spring is correctly placed in the top and bottom nests.
10. Close sponges of a vice plates from a soft material and fix the top support of a rack in a vice.
	11. Tighten a lock nut of a rod the demanded moment. Inhaling moment: 55–68 N • m